设为首页 | 加入收藏您好,欢迎访问上海春普设备有限公司官网!
上海春普
关心你我冷暖、创造舒适空间!
销售热线:021-50341283
工程热线:13601998169

联系我们

CONTACT US

工 程:13601998169
Email:shchunpu@126.com
地 址:上海市浦东新区上南路3855弄如日商务园11号楼602室

行业动态 您的当前位置:首页 >> 新闻中心 >> 行业动态

格力空调故障代码含义及服务方法

发布时间:2019/5/23 10:24:08 浏览次数: 140

E1保护:为系统高压保护。当连续3s检测到高压保护时,关闭除灯箱外的其他负载,屏蔽所有按键及遥控信号,指示灯闪烁并显示故障代码E1.。E2保护:为室内防冻结保护。在制冷、抽湿模式下,压缩机起动6min,连续3min检测到T蒸<-5℃时,指示灯闪烁并显示故障代码E2,停压缩机、外风机;当T蒸>6℃,且压缩机已停足3min时,指示灯灭,液晶恢复显示,原状态运行。不屏蔽按键。

E1 protection: High voltage protection for the system. When high voltage protection is detected for 3 seconds in a row, the load except the light box is turned off, all keys and remote control signals are shielded, and the indicator flashes and the fault code E1 is displayed. E2 protection: for indoor anti-freezing protection. In the mode of refrigeration and dehumidification, when the compressor starts for 6 minutes and detects T steaming <-5 degrees C for 3 minutes, the indicator flashes and displays the fault code E2, stops the compressor and the external fan; when T steaming > 6 degrees C and the compressor has stopped for 3 minutes, the indicator lights go out and the liquid crystal resumes to show the original state of operation. No shielding buttons.



格力空调故障代码含义及服务方法



E3保护:为系统低压保护。压缩机起动3min后开始检测低压开关信号,若连续3min检测到低压开关断开,则整机停,指示灯闪烁并显示故障代码E3,以提示漏氟。E4保护:为排气管高温保护。压缩机起动后,连续30s检测到排气温度高于120℃或排气感温头短路(或开路)时,指示灯闪烁并显示故障代码E4。

E3 protection: low voltage protection for the system. The low-voltage switch signal is detected after the compressor starts for 3 minutes. If the low-voltage switch is disconnected for 3 minutes, the whole machine will stop. The indicator flashes and the fault code E3 is displayed to indicate the leakage of fluorine. E4 protection: high temperature protection for exhaust pipe. After starting the compressor, the indicator flashes and the fault code E4 is displayed when the exhaust temperature is higher than 120 C or the short circuit (or open circuit) of the exhaust temperature sensor is detected for 30 seconds.



格力空调故障代码含义及服务方法



E5保护:为低电压保护。压缩机运转后,若连续3s检测到电流超过25A,指示灯闪烁并显示故障代码E5。EH保护:电加热故障。发出“BB”报警声,红灯闪。当环温>35℃时,强制进入制冷。故障原因如下:交流接触器内部粘连,须更换交流接触器。熔断器工作不正常,须更换熔断器。

E5 Protection: Low Voltage Protection. After the compressor is running, if the current exceeds 25A for 3 seconds, the indicator flashes and the fault code E5 is displayed. EH protection: electrical heating failure. Send out the "BB" alarm sound and the red light flashes. When the annular temperature is higher than 35 C, it is forced to enter the refrigeration. The reasons for the failure are as follows: AC contactor internal adhesion, AC contactor must be replaced. If the fuse is not working properly, the fuse must be replaced.





春普上海中央空调中央从事上海新风系统,写字楼中央空调改造,中央空调改造报价办公楼中央空调

官方网站:http://www.shchunpu.com/


最新内容:
上一篇: 海尔KFR-50、60LW/BPJ×F1和KFR-60LW/BPF变频柜式空调故障代码
下一篇: 格力空调故障代码h1是化霜故障

©2002-2015 上海春普空调设备有限公司  All rights reserved. 备案号:沪ICP09065509号
公司邮箱:shchunpu@126.com       公司地址:浦东新区上南路3855弄11号602室
本站所有商品均提供销售,安装和维修服务。本站内所有产品以实样为准,图片仅供参考。保留最终解释权。
本公司专业从事上海中央空调上海新风系统酒店中央空调改造中央空调改造报价上海格力中央空调办公楼中央空调上海日立中央空调等的销售、设计,安装,售后服务为一体的企业

网站首页 | 关于春普 | 品牌产品 | 新闻中心 | 解决方案 | 工程案例 | 服务支持 | 方案报价 | 联系我们